What Size Block Do You Need To Subdivide In Queensland?

Luke Wiles, Purpose Property buyers agent Brisbane

Luke Wiles

Director at Purpose Property, Luke is a Property Strategist and Chartered Accountant who writes these guides to help local home buyers & investors. If you need help with your property search, just book a free call →

You own a block in Queensland and you're wondering whether it's big enough to subdivide. The answer starts with the planning scheme, not the tape measure. A minimum lot size is one test among many, and each council sets its own.

What a feasibility and logistics report brings together is the full picture: the zone, the overlays, the frontage, the servicing and the lot size requirements specific to your site and your council. Without that, you're working from incomplete information.

Purpose Property helps property owners and small-scale developers across Queensland work out what their site can deliver, and whether the numbers stack up, before they commit.

Here's what the planning schemes say about minimum lot sizes, and why the number on your title is only the starting point.

Key takeaways

  • Minimum lot sizes vary by council, zone and precinct across Queensland.
  • Lot size alone does not decide whether a subdivision will be approved.
  • A Phase 1 feasibility report identifies the real hurdles for your site.

Why the lot size question is harder than it looks

Minimum lot sizes sit inside each council's planning scheme, and each scheme organises them differently: by zone, by precinct within a zone, and sometimes by whether the lot is a front lot or a rear lot. The number that matters for your block depends on which zone it falls in, which precinct applies within that zone, and whether you're creating a rear lot with an access strip.

Getting the zone wrong at the research stage means you're working toward a target that doesn't apply to your land. A town planner and the council's online mapping tools confirm the correct zone before any other calculation begins. Our project consulting process starts here: mapping what the planning scheme says about your site before any money is spent on plans.

What is the minimum lot size to subdivide in Queensland?

There is no single statewide minimum lot size for subdivision in Queensland. The Planning Act 2016 gives each council authority to set its own lot sizes inside its planning scheme. The verified minimum lot sizes below come from three councils whose planning scheme figures are available: Brisbane City Council, Logan City Council and the City of Moreton Bay. Ipswich City Council and the City of Gold Coast set their own minimums, which must be checked directly in their planning schemes.

What the planning schemes say: Brisbane, Logan and Moreton Bay

The table below shows the minimum lot sizes from each council's current planning scheme. These are the published figures for each zone and precinct. Frontage, shape, slope, overlays and the planning scheme's assessment codes also apply, and council decides on each application. A lot that meets the size minimum does not automatically get approved.

Council and zone / precinct Min. lot size (front / rear) Scheme and version
Brisbane – Low density residential (LDR) 450m2 front / 600m2 rear Brisbane City Plan 2014, v37.00/2026
Brisbane – LDR near centres (within 300m walking distance) 300m2 Brisbane City Plan 2014, v37.00/2026 (More Homes, Sooner, effective 18 September 2026)
Brisbane – Character residential (Character precinct) 450m2 front / 600m2 rear Brisbane City Plan 2014, v37.00/2026
Brisbane – Character residential (Infill housing precinct) 300m2 front / 450m2 rear Brisbane City Plan 2014, v37.00/2026
Brisbane – Low-medium density residential (LMR), small lots From 120m2 (outside Key Locations, where design criteria are met) Brisbane City Plan 2014, v37.00/2026 (More Homes, Sooner, effective 18 September 2026)
Brisbane – Rural residential 10,000m2 Brisbane City Plan 2014, v37.00/2026
Logan – LDR, Small lot precinct 300m2 (rear lots not permitted) Logan Planning Scheme 2015, v9.2 (from 1 July 2025)
Logan – LDR, Suburban precinct 400m2 front / 500m2 rear (clear of access strip) Logan Planning Scheme 2015, v9.2 (from 1 July 2025)
Logan – LDR, Village precinct 500m2 front / 600m2 rear (clear of access strip) Logan Planning Scheme 2015, v9.2 (from 1 July 2025)
Logan – LDR, Large suburban precinct 1,000m2 front / 1,000m2 rear (clear of access strip) Logan Planning Scheme 2015, v9.2 (from 1 July 2025)
Logan – LDR, Small acreage precinct 2,000m2 front / 2,000m2 rear (clear of access strip) Logan Planning Scheme 2015, v9.2 (from 1 July 2025)
Logan – LDR, Acreage precinct 4,000m2 (rear lots not permitted) Logan Planning Scheme 2015, v9.2 (from 1 July 2025)
Logan – Low-medium density residential, Townhouse precinct 500m2 (rear lots not permitted) Logan Planning Scheme 2015, v9.2 (from 1 July 2025)
Logan – Low-medium density residential, Apartment precinct 800m2 (rear lots not permitted) Logan Planning Scheme 2015, v9.2 (from 1 July 2025)
Logan – Medium density residential 1,200m2 Logan Planning Scheme 2015, v9.2 (from 1 July 2025)
Moreton Bay – General residential, Coastal communities precinct 600m2, 12.5m frontage (preliminary guide, max 11 lots/ha) Moreton Bay Planning Scheme 2016, v7.1 (effective 23 June 2025)
Moreton Bay – General residential, Suburban neighbourhood precinct 600m2, 12.5m frontage (preliminary guide, max 11 lots/ha) Moreton Bay Planning Scheme 2016, v7.1 (effective 23 June 2025)
Moreton Bay – Next generation neighbourhood precinct No stated minimum (10 to 25 lots per hectare; narrow lots supported) Moreton Bay Planning Scheme 2016, v7.1 (effective 23 June 2025)

Council fees change each financial year, and the planning scheme figures above may be updated when a scheme is amended. Always check the current planning scheme version and fee schedule for your council before you budget.

How Does Purpose Property's Project Consulting Help You Assess Your Block's Subdivision Potential in Queensland?

A lot size check is a starting point. What a Phase 1 feasibility and logistics report adds is the full picture of what your site can and can't deliver: the zone, the overlays, the frontage requirements, the servicing questions and the assessment pathway. That's what turns a size check into a decision you can act on.

Step 1: Book a free strategy call

Get in touch with Purpose Property and we'll talk through your site, your council area and what you're hoping to achieve before any money is spent.

Step 2: Phase 1 feasibility and logistics report

We prepare a practical report on your site through our project consulting process, covering the development pathways the site could support, the planning scheme zone and overlays, the hurdles to each pathway and the consultants each one needs.

Step 3: Walk through the findings in a 45 minute consult

We walk you through the report in a 45 minute consult, covering the practical next steps and the questions to take to your town planner, registered surveyor and engineer.

Step 4: Choose your pathway (develop, hold or sell)

With the feasibility findings in hand, you decide whether to develop, hold or sell. We help you weigh the options from an investor's perspective, without predicting outcomes we can't confirm.

Step 5: Build the team

We source and review registered surveyors, town planners, RPEQ engineers, designers and builders, so you're not starting from scratch when the time comes to move.

Step 6: Coordinate through to completion

We track progress across every part of the project, review key documents from an investor's perspective, and keep every party aligned so nothing falls through the cracks.

Get in touch

Not sure whether your block meets the minimum lot sizes?

A free strategy call shows whether a feasibility report suits your site.

What happens when owners start a project without checking the lot size rules

The most expensive mistake in a small Queensland subdivision is commissioning a surveyor or town planner for a layout that the planning scheme rules out before the application is lodged. You've paid for plans, paid for a pre-lodgement, and then discovered the zone doesn't allow what you assumed. Starting a subdivision without a feasibility check is a bit like signing a building contract before seeing the plans: you might get what you expected, but the surprises tend to be expensive.

Lot size is only one part of the assessment. Even a block that clearly meets the minimum area for its zone and precinct can face hurdles at the frontage, slope, overlay, servicing or assessment-type stage. Reconfiguring a lot is code assessable by default in Logan, for example, but it becomes impact assessable when the proposed lots fall below the precinct's minimum. Impact assessment brings public notification and a longer process. Knowing which pathway applies to your site before you start changes what the project costs and how long it takes.

"Most of the expensive surprises in a project can be found before you spend anything on plans. Check what the site can deliver and where the hurdles are, then decide whether to develop, hold or sell."

Luke Wiles, Director and Principal Buyers Agent, Purpose Property

What else a council looks at beyond the lot size

  • Frontage: each planning scheme sets minimum frontage requirements for each zone and precinct. Logan's Suburban precinct, for example, requires a minimum 12.5m normal frontage, 10m for a cul-de-sac lot and 15m for a corner lot. Brisbane minimum frontage figures are not published in a single verified source: your town planner checks the Subdivision code in City Plan. Moreton Bay's Suburban neighbourhood precinct sets 12.5m as a preliminary guide.
  • Rear lots and access strips: rear lot minimums are measured clear of the access strip. In Logan's Suburban precinct, the minimum rear lot area clear of the strip is 500m2. Rear lots are not permitted in Logan's Small lot, Acreage or Apartment precincts.
  • Overlays: a flood overlay, environmental management overlay, bushfire hazard overlay or heritage overlay can restrict what is possible on a site, regardless of the lot size. Council mapping tools and the planning scheme identify these before any application is prepared.
  • Assessment pathway: a proposal that meets every size, frontage and overlay requirement is code assessable. A proposal that falls below the minimums in any category shifts to impact assessment, which requires public notification, a broader assessment and a longer process. Knowing which pathway applies upfront changes the cost and risk profile of the project.
  • Servicing: each new lot needs water supply, sewerage, stormwater and road access. Who provides those services depends on the council area. In Brisbane and Ipswich, Urban Utilities handles water and sewerage; in Logan, Logan Water (part of the council) provides it; in Moreton Bay, Unitywater does. The cost and complexity of connections is confirmed per site by the relevant utility and a registered engineer.
  • Infrastructure charges: once approved, an infrastructure charges notice is issued. The charge is set in the council's charges resolution and is generally payable when the plan of subdivision is approved. In Logan City Council, under the Logan Charges Resolution (No. 12) 2025, the adopted charge is $36,670.70 per lot for reconfiguring a lot (from 1 September 2025). This is a combined charge that includes water and sewer. Council fees and charges change each financial year: check the current resolution and Logan City Council's fee schedule before you budget.

Ipswich and Gold Coast: check the planning scheme directly

Minimum lot sizes for subdivision in the Ipswich City Plan 2025 and the Gold Coast City Plan (Version 13, commenced 9 December 2025) are not published in a single verified source for this article. Your town planner checks the Reconfiguring a lot code in the Ipswich City Plan 2025 ePlan and the relevant zone provisions in the Gold Coast City Plan for your site's specific zone and precinct. In the City of Gold Coast, subdivision is code assessable in all zones if the required lot sizes are met: proposals below the stated minimum need impact assessment. Always confirm directly with the relevant council or a town planner before drawing any conclusions about a Gold Coast or Ipswich site.

Frequently Asked Questions

Is there a statewide minimum lot size for subdivision in Queensland?

No. The Planning Act 2016 gives each council authority to set its own minimum lot sizes inside its planning scheme. Brisbane, Logan and Moreton Bay each set different minimums by zone and precinct, and Ipswich and Gold Coast set their own figures that must be checked in their planning schemes directly.

What is the minimum lot size to subdivide in Logan City?

In Logan's Low density residential zone, the minimum ranges from 300m2 in the Small lot precinct to 4,000m2 in the Acreage precinct, under the Logan Planning Scheme 2015 v9.2 (from 1 July 2025). The Suburban precinct minimum is 400m2 for a front lot and 500m2 clear of the access strip for a rear lot. Which precinct applies to your block is confirmed in the Logan PD Hub online mapping tool.

What changed for subdivision in Brisbane after the More Homes, Sooner amendment?

From 18 September 2026, Brisbane's Low-medium density residential zone allows small lots from 120m2 where the design and built form criteria are met, and the Low density residential zone allows 300m2 lots within 300m walking distance of a shopping centre. These changes came with the citywide More Homes, Sooner amendment to Brisbane City Plan 2014 v37.00/2026.

Does meeting the minimum lot size mean subdivision will be approved?

Not necessarily. Minimum lot size is one test of several. Frontage, shape, slope, overlays (such as flood or heritage) and the planning scheme's assessment codes also apply, and council decides on each application. A site that meets the area minimum can still face hurdles at the frontage, overlay or servicing stage.

What is the difference between code assessable and impact assessable subdivision?

Code assessable means the application is assessed only against the planning scheme's benchmarks, with no public notification. Impact assessable applies when a proposal falls below the planning scheme's minimums or triggers certain overlays: it involves a broader assessment, public notification and submissions, which adds cost and time. Knowing which pathway applies before you lodge changes the project's risk profile significantly.

What does a project consultant do that a builder or town planner doesn't?

A project consultant works for you, the owner, across the whole project. A town planner focuses on the planning application, a builder focuses on construction, and a certifier assesses the building work. A project consultant sources and reviews all of those parties, tracks progress across every part of the project, reviews key documents from an investor's perspective and keeps communication aligned so nothing is missed.

Do I need a registered surveyor to subdivide in Queensland?

Yes. Only surveyors registered with the Surveyors Board of Queensland can carry out cadastral surveys, which are the surveys that create or change property boundaries. The registered surveyor surveys the land, designs the lot layout and prepares the plan of subdivision that is lodged with council and ultimately registered with Titles Queensland to create the new titles.

Your Next Steps

Getting the lot size question right is only the beginning. The zone, the precinct, the overlays, the frontage and the servicing all have to stack up before a subdivision application has a realistic path to approval, and each of those checks is site-specific.

Ready to find out what your block can actually deliver? Contact Luke Wiles for a free strategy call or call 0414 663 531. We will map your site's development pathways and hurdles, and show whether the numbers stack up before you spend on plans.

Purpose Property · Greenslopes, QLD · General information only: this article does not constitute financial, legal, planning, engineering or investment advice. Purpose Property does not provide legal, financial, taxation, town planning, engineering or other professional advice. Please consider your own circumstances and seek independent advice from qualified professionals before making any property, development or investment decisions.

Luke Wiles, Director and Principal Agent at Purpose Property

By Luke Wiles

Luke Wiles is the Director and Principal Agent of Purpose Property. A Property Strategist and Chartered Accountant, he has built his own property portfolio, now worth over $10 million, and helps buyers and investors across South East Queensland and Victoria find the right property, at the right price, in the right location.

Purchasing property? Book a Free strategy session with our local buyers agents today.


✔ Gain clarity on what to buy and where.


✔ Save time and move forward confidently with a streamlined, step-by-step process.

✔ Learn from a mentor who has successfully built their own high-performing property portfolio.


✔ Partner with a proven strategist who openly shares the insights, frameworks, and strategies behind their success.


If you’re looking to make smarter property decisions and accelerating your results, our  Buyers Agent Brisbane team can help, simply  schedule a free call today or get in touch below.

Email: hello@purposeproperty.com.au
Phone:
 0414 663 531